Bettis Electric Actuators: XTE3000 & M2CP
Current Bettis Models for New Valves and Legacy EIM Replacements
Where Electric Actuator Orders Get Stuck
- Finding an authorized source instead of a reseller. TRIVACO is an authorized Emerson distributor for Bettis electric actuators in Kentucky, Ohio, and Indiana. Orders through us carry the standard 12-month warranty from shipment. Authorization is set by territory, so one call tells you whether your site falls in ours.
- Lead time surfacing too late. Factory lead time on a standard Bettis actuator runs 8 to 10 weeks. That can push delivery past your outage window if the order goes in late. We stock some M2CP actuators and parts. Every quote lists the lead time up front, ahead of the PO.
- An EIM unit that's out of production. Emerson discontinued the EIM MCP in 2018. The Bettis M2CP is its listed replacement and keeps the same Series 2000 mechanical design. Send a nameplate photo. We'll match the model and flag any mounting changes.
- The spec came from whatever was installed last. Replacement in kind works until the duty changes. A valve that once opened a few times an hour may now need modulating duty, which Emerson rates at up to 1,200 starts per hour. Emerson notes that an under-specified duty cycle hurts performance, while an over-specified one adds cost. We check torque, speed, and duty against today's service.
- The controls don't match the system. An actuator that arrives with the wrong control card or protocol holds up startup. The XTE3000 supports Modbus, HART, FOUNDATION Fieldbus, PROFIBUS, and LonWorks. The M2CP supports DeviceNet and Ethernet in place of LonWorks. We confirm the protocol and area classification when we quote.
Bettis Electric Actuators We Supply
Bettis XTE3000 Electric Actuator
The XTE3000 is a non-intrusive multi-turn actuator that Emerson built for oil and gas, power, and process plants. Setup and diagnostics happen through the closed cover.
- Push-button and Bluetooth® setup. Operate, configure, and run diagnostics with the control compartment sealed.
- Position after a power loss. The absolute encoder reads valve position even when main and backup power are lost.
- Recorded maintenance data. The datalogger keeps operating data, alarms, and valve torque curves for review in Emerson’s DCMlink software.
- Declutchable manual override. On an electrical command, an internal spring-loaded clutch disengages the handwheel and re-engages the motor drive. The handwheel won’t spin under motor power, which protects the technician.
- Fieldbus options. Modbus®, HART®, FOUNDATION™ Fieldbus, PROFIBUS, and LonWorks®.
Bettis M2CP Electric Valve Actuator
The M2CP is a conventional, heavy-duty actuator with the same mechanical design as the EIM Series 2000. Emerson built it for harsh service and field repair.
- Screwdriver service. The control package comes out, comes apart, and goes back in with a standard screwdriver.
- Hand operation on a seated valve. A power shift clutch moves the M2CP to handwheel operation with little force. The clutch handle padlocks in hand or motor position.
- Motor options. Most single-phase and three-phase AC voltages, plus DC.
- Shock and vibration. Meets DOD-V-24657(SH) high shock and MIL-STD-167-1 and MIL-STD-901D mechanical vibration standards.
- Network options. Modbus, HART, FOUNDATION Fieldbus, PROFIBUS, DeviceNet™, and Ethernet.
Bettis XTE3000 vs. M2CP Specifications
Spec
Bettis XTE3000
Bettis M2CP
Choose the XTE3000 for On-Device Setup and Diagnostics
The XTE3000 suits plants that want local configuration, Bluetooth access, recorded torque curves, and DCMlink diagnostics.
Choose the M2CP for Severe Service or an Existing EIM Fleet
Replacing EIM M2CP and MCP Actuators
The Bettis M2CP is the EIM M2CP under the Bettis name. It keeps the Series 2000 mechanical design that dates to 1979. Many parts interchange across the M2CP and Series 2000 range, so upgrades often fit units already in service. For the EIM MCP, which Emerson discontinued in 2018, the Bettis M2CP is the listed replacement.
Replacing an EIM unit? Email a photo of the nameplate to [email protected]. We’ll quote the Bettis model that fits your valve.
Buying for resale? We supply Bettis electric actuators through the distribution channel, as loose actuators or as complete automated valve assemblies.
Where Bettis Electric Actuators Are Used
Oil and Gas Transmission
Power Generation (Fossil and Hydro)
Chemical Process and Refineries
Tank Farms
Municipal Water and Wastewater Treatment
Steel, Aluminum, and Pulp and Paper
Sizing a Bettis Electric Actuator
What to send with your quote request:
- Valve type and stroke. Multi-turn (gate, globe), quarter-turn (ball, butterfly, plug), or linear. For multi-turn valves, include the number of turns.
- Torque or thrust. Give the valve’s required operating torque or thrust. Emerson’s XTE3000 data sheet notes that stall torque can reach 2 times nominal torque, depending on speed and voltage. Check that the valve stem and mounting can take that load.
- Duty cycle. Opening and closing an isolation valve is short-time duty (S2). Modulating duty (S4) runs up to 1,200 starts per hour. Emerson notes that an under-specified duty cycle hurts performance, while an over-specified one adds cost.
- Operating time. How fast the valve has to stroke open or closed.
- Power supply. Voltage, phase, and frequency, or DC. The XTE3000 isn’t available above 600 V.
- Controls. Hardwired signals or the network protocol your system uses.
- Area classification and ambient temperature. The hazardous-area class and division (or zone), plus the site’s low and high temperatures.
Already Have EIM or Bettis Actuators in Service?
TRIVACO supplies the actuator alone or as part of a complete automated valve assembly. Our team mounts the actuator to your valve, tests the assembly, and supports startup in the field. Our Valve Repair Shop and Field Service and Installation team also work on EIM and Bettis units already in your plant. For networks of actuators, our UL Panel Shop builds the control panels that tie them to your system.
TRIVACO has been selling and servicing electric actuators for over 35 years.
Warranty: Bettis actuators carry a standard 12-month warranty from the date of shipment.
Resources
Also From TRIVACO
Need the valve as well? Our Valves and Automation category covers the isolation valves, control valves, and pneumatic actuators we pair with electric units. For overpressure protection on the same lines, see Safety Valves & Pressure Relief Devices.
Safety Valve Questions We Get Asked
What is a Bettis electric actuator used for?
What's the difference between the Bettis XTE3000 and the M2CP?
Is the Bettis M2CP the same as the EIM M2CP?
What replaced the EIM MCP actuator?
Can an electric actuator replace a pneumatic actuator?
Which communication protocols do they support?
Are Bettis electric actuators rated for hazardous areas?
Do you stock Bettis actuators, or is everything built to order?
Can TRIVACO repair EIM and Bettis actuators?
How much does a Bettis electric actuator cost?
Request a Quote for Bettis Electric Actuators
Tell us about the valve and how you control it. TRIVACO turns quotes around the same day or the next day, with a sized recommendation, a written quote, and a lead time. If you’re replacing an EIM unit, attach a photo of the nameplate.