Safety Valve Repair
Your Safety Valve Isn't Just Broken. Your Process Is Losing Ground.
Generic repair shops restore function. TRIVACO restores performance, engineered to the tolerances your control loops, safety systems, and next inspection actually demand.
Looking for new valves rather than repair? Browse our safety valve lineup, where you can compare replacement units and get sizing help before you order.
OUR CERTIFICATIONS
Delays on a safety valve repair usually come from a shop that has to route the work through a third party, or from paperwork that doesn’t satisfy the inspector on the first pass. Not at TRIVACO. We hold these certifications so your job stays in one building and the documentation is finished when the valve ships.
Repair Gets You Running. Optimization Keeps You There.
Most safety valve failures don’t announce themselves with a catastrophic event. They show up first as control loop instability, unexplained process variance, or a relief device that lifts slightly off setpoint during a normal operating cycle. A valve that passes a basic function test can still be costing you throughput, and it will cost you more during your next inspection.
TRIVACO’s safety valve repair process combines certified restoration with diagnostic-level evaluation, so when your valve returns to service, your process performs the way it was designed to. That evaluation draws on 55+ years of industrial valve experience, and it usually ends in a repair rather than a purchase order. Customers save up to 70% against the cost of replacing the valve outright.
When the valve can’t leave the unit, our mobile VR trailer and lift assist bring the shop to your site. Same certified process, same documentation, no crane rental on your end.
Safety Relief Valve Repair You Can Document at the Next Inspection
Safety relief valves protect personnel, equipment, and your facility’s operating license. When they fail to lift at setpoint — or fail to reseat — the consequences are measured in incidents, not inconvenience.
TRIVACO holds three National Board VR Certificates across four regional shops, authorizing us to inspect, verify, and re-establish OEM specifications for all critical parts, then set every device within ASME-specified tolerances using calibrated measurement and test equipment, with full documentation retained.
That distinction matters. A “test only” is a basic pop test that may have been performed by an organization with no demonstrated level of quality or competency. If an unrecognized organization repairs or cuts the lead seals on an ASME device, that valve no longer falls under ASME or National Board certification. There is no recognized standard for the set pressure or relieving capacity of a valve serviced outside a certified VR program.
- Disassembly, cleaning, and dimensional inspection
- Lapping or replacement of nozzle and disc seating surfaces
- Spring inspection and replacement to OEM specification
- Set pressure verification and adjustment within ASME-specified tolerances
- Seat tightness verification
- Bead blasting to restore to like-new condition
- VR-stamped nameplate and full National Board documentation
We also hold the ASME V Stamp (Section I — power boiler safety valves), ASME UV Stamp (Section VIII — pressure vessel safety valves), and the National Board NB Stamp for Registration and Capacity Certification.
Your Valve History. Accessible. Permanent.
One of the most consistent failure points in industrial maintenance programs isn’t the valve — it’s the paperwork. Service records that live in a technician’s head. Test data that doesn’t survive a personnel transition. Certification documents that can’t be located at inspection time.
ValvKeep® Asset Management Software gives you a web-based, always-accessible record of every valve we’ve touched: repair history, test data, set pressures, parts used, and certification documentation — organized by tag number and accessible to your team from any browser.
When your inspector asks for the last SRV service record, you have it. When you’re troubleshooting a control valve for the third time in two years, you can see why.
National Board Certified Relief Valve Restorations
Three Shops and Certified Regions. One Quality Standard
Understand Our Full Capabilities by Location, Testing Ranges and Service Descriptions
Also Available: Baker Hughes Masoneilan Authorized Repair Center (MARC)
Beyond safety valve work, TRIVACO’s Canton, GA shop holds Baker Hughes Masoneilan Authorized Repair Center status. If your facility also runs Masoneilan control valves, the same shop can handle them: factory-certified to inspect, diagnose, repair, recalibrate, and return those valves using OEM parts, factory procedures, and the right tooling.
That certification matters when you need warranty status preserved, manufacturer-traceable service records, or documentation that holds up in a regulated environment.
Masoneilan control valve service at TRIVACO includes:
- Factory-trained technicians with Masoneilan-specific expertise
- Genuine OEM parts meeting original manufacturer standards
- Commissioning and startup support for new equipment
- Retrofit and upgrade services for modernizing aging assets
- EVT-Pro predictive monitoring to catch issues before they cause failures
- Complete inspection reports and service records for compliance and asset management